Max TA238A/18-6 Manuel d'utilisateur télécharger pdf (Page 5)

13. PLACE THE DISCHARGE OUTLET ON THE WORK SUR-

FACE PROPERLY

Failure to place the discharge outlet of the nose in a proper

manner can result in a fastener flying up and is extremely

dangerous.

14. KEEP HANDS AND BODY AWAY FROM THE DIS-

CHARGE OUTLET

When loading and using the tool, never place a hand or any

part of body in fastener discharge area of the tool. It is very

dangerous to hit the hands or body by mistake.

15. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE

AND CORNER OF THE WORK AND THIN MATERIAL

The workpiece is likely to split and the fastener could fly free

and hit someone.

16. DO NOT DRIVE FASTENERS ON TOP OF OTHER FAS-

TENERS

Driving fasteners on the top of other fasteners may cause

deflection fasteners which could cause injury.

17. REMOVING THE FASTENERS AFTER COMPLETING

OPERATION

If fasteners are left in the magazine after the completion of

operation, there is the danger of a serious accident occur-

ring prior to the resumption of operation, should the tool be

handled carelessly, or when connecting the air fitting. For

this reason, always remove all fasteners remaining in the

magazine after completion of the operation.

18. CHECK OPERATION OF THE CONTACT TRIP MECHA-

NISM FREQUENTLY INCASE OF USING A CONTACT

TRIP TYPETOOL

Do not use the tool if the trip is not working correctly as ac-

cidental driving of a fastener may result. Do not interfere

with the proper operation of the contact trip mechanism.

19. WHEN USING THE TOOL OUTSIDE OR ELEVATED

PLACE

When fastening roofs or similar slanted surface, start fas-

tening at the lower part and gradually work your way up.

Fastening backward is dangerous as you may lose your foot

place.

Secure the hose at a point close to the area you are going

to drive fasteners. Accidents may be caused due to the

hose being pulled inadvertently or getting caught.

20. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL

CONTROLS (e.g., TRIGGER, CONTACT ARM) IS INOP-

ERABLE, DISCONNECTED, ALTERED OR NOT WOK-

ING PROPERLY

21. NEVER ACTUATE THE TOOL INTO FREE SPACE

This will avoid any hazard caused by free flying fasteners

and excessive strain of the tool.

22. ALWAYS ASSUME THAT THE TOOL CONTAINS FAS-

TENERS

23. RESPECT THE TOOL AS A WORKING IMPLEMENT

24. NO HORSEPLAY

25. NEVER LOAD THE TOOL WITH FASTENERS WHEN

ANY ONE OF THE OPERATING CONTROLS (e.g., TRIG-

GER, CONTACT ARM) IS ACTIVATED

26. WHEN DISPOSING THE MACHINE OR ITS PARTS, FOL-

LOW THE RELEVANT NATIONAL RULES

OBSERVE THE FOLLOWING GENERAL CAU-

TION IN ADDITION TO THE OTHER WARNINGS

CONTAINED IN THIS MANUAL

• Do not use the tool as a hammer.

• Always carry the tool by the grip, never carry the

tool by the air hose.

• The tool must be used only for the purpose it was

designed.

• Never remove, tamper with the operating controls

(e.g., TRIGGER, CONTACT ARM)

• Keep the tool in a dry place out of reach of chil-

dren when not in use.

• Do not use the tool without Safety Warning label.

• Do not modify the tool from original design or

function without approval by MAX CO., LTD.

TA238A-USA.book 5 ページ２０１０年７月９日　金曜日　午後５時３７分

1 2 3 4 5 6 7 8 9 10 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Max TA238A/18-6 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Max TA238A/18-6